抹面砂漿是由石英砂、水泥、聚合物膠結料配合著多種添加劑經(jīng)機械地混合均勻而成的。那么濟南抹面砂漿怎樣正確的使用呢？

The plastering mortar is mechanically mixed by quartz sand, cement, polymer cement and various additives. So how to use Jinan plastering mortar correctly?

抹面砂漿不應該小于1800千克/立方米。在水泥或著是石灰砂漿中摻加進適當?shù)膿胶狭希热绶勖夯摇⒐柙逋恋鹊?，以?jié)約水泥或者是石灰用量，同時，改善一下砂漿的和易性。常常用到的混合砂漿有水泥石灰砂漿、石灰粘土砂漿和水泥粘土砂漿等等。

The plastering mortar shall not be less than 1800 kg/m3. Add appropriate admixtures, such as fly ash, diatomite, etc., into cement or lime mortar to save the amount of cement or lime and improve the workability of mortar. The commonly used mixed mortar includes cement lime mortar, lime clay mortar and cement clay mortar.

砂漿的攪拌方式時采用開機加上部分砂再加上砂漿稠化增強劑、1/3水、部分砂、水泥、全部水和砂。干混砂漿隨拌隨用，一般在攪拌成后的4個小時里面使用完畢，當施工期間，氣溫超過30℃的時候，須在拌完成之后的3小時里面使用完畢。

The mixing method of mortar is to start the machine, add some sand, and then add mortar thickener, 1/3 water, some sand, cement, and all water and sand. Dry mixed mortar can be used at any time. It is generally used within 4 hours after mixing. During construction, when the temperature exceeds 30 ℃, it must be used within 3 hours after mixing.

把砂漿稠化增強劑放進砂漿之后，可以減少拌合物的用水量，在攪拌的時候要控制好用水量，其減水率應該為20%。為了方便配料，也為了減少施工中的切鋸工作量，在建筑施工中，要進行排塊的設計。干混砂漿要嚴格控制好加氣混凝土砌塊上墻砌筑的時候的含水率。

The water consumption of the mixture can be reduced after the mortar thickening reinforcement agent is put into the mortar. The water consumption should be controlled well during mixing, and the water reduction rate should be 20%. In order to facilitate batching and reduce the sawing workload in construction, block arrangement design shall be carried out in construction. The moisture content of dry mixed mortar shall be strictly controlled during the wall masonry of aerated concrete block.

抹面砂漿的作用

Function of plastering mortar

(1)底層砂漿的作用是使砂漿和基層能牢固地粘結在一起，有良好的保水性能。

(1) The function of the base mortar is to make the mortar and the base firmly bonded together and have good water retention performance.

(2)中層砂漿主要是為了找平，因此，有時候中層砂漿可以省去不做。

(2) The intermediate mortar is mainly used for leveling, so sometimes it can be omitted.

(3)面層砂漿主要為了能產生平整、光潔的表面效果。因此，各層抹面砂漿的作用不同，基底材料的特性不同，對砂漿技術性能要求也不同。更多相關事項就來我們網(wǎng)站http://www.sjzmx.cn咨詢吧！

(3) The surface mortar is mainly used to produce a flat and smooth surface effect. Therefore, the function of each layer of plastering mortar is different, the characteristics of base materials are different, and the technical performance requirements for mortar are also different. Come to our website for more information http://www.sjzmx.cn Consult!