What is the construction process of Jinan putty powder?

一．模子

1、 Mold

原因：

reason:

濟南膩子粉廠家在墻地幕墻時，其原料是海藻和水泥的混合物，其酸堿度較高，因此踢腳也比較容易，它會與p反應對濕線和帶有壁泄漏的區域進行反應。這種現象會導致壁上的翅膀，發霉并剝落皮膚。

When Jinan putty powder manufacturer is in the wall and ground curtain wall, its raw material is the mixture of seaweed and cement. Its pH is high, so it is easy to skirting. It will react with P to react with the wet line and the area with wall leakage. This phenomenon can cause the wings on the wall to become moldy and peel off the skin.

加工方式：

Processing method:

可以干凈地除去發霉的無殼壁，并可以清洗干凈的水，并且如果泄漏或潮濕的壁可以立即關閉水源，并且可以在壁干燥后再次去除堿性粉末。

The moldy shell free wall can be removed cleanly, and the clean water can be cleaned. If the wall is leaked or wet, the water source can be turned off immediately, and the alkaline powder can be removed again after the wall is dry.

注意：通常，墻壁發霉，春季天氣基本炎熱。

Note: usually, the walls are moldy, and the weather is basically hot in spring.

二．做快點

2、 Do it quickly

原因：

reason:

1.由于夏季天氣相對炎熱，水的蒸發相對較快，而在批量除塵工作中水的揮發相對較快。出現的比路還多。

1. Due to the relatively hot weather in summer, the evaporation of water is relatively fast, while the evaporation of water in batch dust removal is relatively fast. There are more than roads.

2.生產原因：發生速干現象的原因是生產商無意中誤認為原料的混合比例，或者由于設備異常而使混合變得不穩定。

2. Production reasons: the reason for the quick drying phenomenon is that the manufacturer inadvertently mistook the mixing proportion of raw materials, or the mixing became unstable due to abnormal equipment.

加工方式：

Processing method:

1.施工時的天氣為35°C，在稀薄的鼓風機和物料攪拌下，接下來的兩種或多種膩子粉的使用方法很少。

1. The weather during construction is 35 ° C. under the mixing of thin blower and materials, the next two or more putty powders are rarely used.

2.出現速干現象時，濟南膩子粉廠家工程師會到現場，根據產品的配方判斷是否速干。

2. In case of quick drying, the engineer of Jinan putty powder manufacturer will come to the site to judge whether it is quick drying according to the product formula.

注意：如果出現速干現象，則可以像之前一樣在進行約2小時的表面干燥后立即進行下一次構造，從而減少速干。

Note: if rapid drying occurs, the next construction can be carried out immediately after about 2 hours of surface drying as before, so as to reduce rapid drying.

三．針孔

3、 Pinhole

原因：

reason:

1.正?，F象是在一批時出現針孔。在一批的情況下，粉末層厚且難以弄平，這影響了在弄平后第2條的粘合力。針孔通常在墻壁相對不平坦的一些道路上形成，但由于針孔吃掉了大量材料，針孔會緩慢干燥，并且經紗上鋪有凹陷的粉末。由于困難，所以發生針孔現象。

1. The normal phenomenon is pinholes in a batch. In the case of a batch, the powder layer is thick and difficult to flatten, which affects the adhesion of Article 2 after flattening. Pinholes are usually formed on some roads with relatively uneven walls, but because the pinholes eat a lot of material, the pinholes will dry slowly, and the warp yarn is covered with concave powder. Pinholes occur due to difficulties.

膩子粉廠家

Putty powder manufacturer

2.由于施工過程中光線不足，濟南膩子粉廠家施工人員在施工過程中會忽略墻面上的小針孔，因而無法及時接收，從而造成針孔現象。

2. Due to the lack of light during construction, the construction personnel of Jinan putty powder manufacturer will ignore the small pinholes on the wall during construction, so they cannot receive them in time, resulting in pinholes.

加工方式：

Processing method:

1.對于不平坦的墻壁，在一個施工過程中必須使平面盡可能平整。

1. For uneven walls, the plane must be as flat as possible during a construction process.

2.施工時要小心，天氣不好時光線不足，或者晚上天黑時，要在腋下用照明設備進行施工，濟南膩子粉廠家會避免施工錯誤，要用人造針進行施工避免孔洞問題。

2. Be careful during construction. When the weather is bad, the time line is insufficient, or it is dark at night, the construction shall be carried out with lighting equipment under the armpit. Jinan putty powder manufacturer will avoid construction errors and use artificial needles to avoid hole problems.

如果膩子粉的粉末太粘或太慢，可能會出現針孔，因此必須注意產品配方的合理性。

If the powder of putty powder is too sticky or too slow, pinholes may appear, so we must pay attention to the rationality of the product formula.