抹面砂漿的使用標準主要參照以下幾個方面：

The usage standards for plastering mortar mainly refer to the following aspects:

技術規程：《抹灰砂漿技術規程》JGJT220-2010 是關于抹面砂漿使用的重要行業標準，規定了抹面的術語和定義、一般規定、要求、試驗方法、檢驗規則、產品合格證和使用說明書、包裝、運輸和貯存等內容。

Technical specification: JGJT220-2010 is an important industry standard for the use of plastering mortar, which specifies the terminology and definitions, general regulations, requirements, test methods, inspection rules, product qualification certificates and user manuals, packaging, transportation, and storage of plastering mortar.

性能指標：抹面砂漿（抹面膠漿）的性能指標包括拉伸粘結強度原強度、可操作時間等。

Performance indicators: The performance indicators of plastering mortar (plastering adhesive) include tensile bonding strength, original strength, operable time, etc.

抗壓強度和抗拉強度：抹面砂漿的抗壓強度一般要求在10MPa以上，抗拉強度要求在1.5MPa以上。

Compressive strength and tensile strength: The compressive strength of plastering mortar is generally required to be above 10MPa, and the tensile strength is required to be above 1.5MPa.

粘結強度：抹面砂漿與基層墻面的粘結強度一般要求在0.5MPa以上。

Bonding strength: The bonding strength between the plastering mortar and the base wall surface is generally required to be above 0.5MPa.

施工性能：包括凝結時間、可調整時間、初始鋪涂性等。

Construction performance: including setting time, adjustable time, initial spreading ability, etc.

配合比例和原材料品質：國標還規定了抹面砂漿的配合比例、原材料品質要求、檢測方法等。

Mixing ratio and raw material quality: The national standard also specifies the mixing ratio, raw material quality requirements, and testing methods for plastering mortar.

預拌砂漿：多層機噴砂漿抹面系統不得采用人工拌制砂漿，宜使用預拌砂漿。

Pre mixed mortar: The multi-layer machine sandblasting slurry plastering system shall not use manual mixing of mortar, and pre mixed mortar should be used instead.

砂漿性能：多層機噴砂漿抹面系統所用筋條砂漿、底層砂漿、中層砂漿及面層砂漿除應符合現行國家標準《預拌砂漿》GB/T 25181 的規定外，尚應符合表 3.2.2 的規定，包括入泵砂漿稠度、保水率、分層度、凝結時間、28d 抗壓強度、14d 拉伸粘結強度、28d 收縮率等。

Mortar performance: The reinforcement mortar, bottom mortar, middle mortar, and surface mortar used in the multi-layer machine sandblasting slurry plastering system should not only comply with the current national standard "Ready mixed Mortar" GB/T 25181, but also comply with the provisions of Table 3.2.2, including the consistency, water retention rate, layering degree, setting time, 28 day compressive strength, 14 day tensile bonding strength, 28 day shrinkage rate, etc.

界面砂漿性能：多層機噴砂漿抹面系統所用界面砂漿的性能指標應符合表 3.2.3 的規定，包括拉伸粘結強度、晾置時間等。

Interface mortar performance: The performance indicators of the interface mortar used in the multi-layer machine sandblasting slurry plastering system should comply with the provisions of Table 3.2.3, including tensile bond strength, drying time, etc.

原材料要求：預拌砂漿所用原材料除應符合現行國家標準《預拌砂漿》GB/T 25181 的規定外，尚應符合其他相關規定。

Raw material requirements: In addition to complying with the current national standard "Ready mixed Mortar" GB/T 25181, the raw materials used for pre mixed mortar should also comply with other relevant regulations.

以上是抹面砂漿使用的主要標準和要求，生產與使用抹面砂漿時，應按照這些標準進行操作，以確保施工質量和建筑物的安全可靠性。

The above are the main standards and requirements for the use of plastering mortar. When producing and using plastering mortar, these standards should be followed to ensure construction quality and the safety and reliability of buildings.

本文由濟南抹面砂漿為您提供，我們的網站http://www.sjzmx.cn我們將以全心全意的熱情為您提供服務，歡迎您的訪問

This article is provided by Jinan plastering mortar for you on our website http://www.sjzmx.cn We will provide you with wholehearted enthusiasm and welcome your visit